Tascam 48 Amp Cards

Things are coming together slowly, equipment-wise. I wanted to use my 1/2″ 8-track, a Tascam 48-OB, so I hooked it up to the mixer and went at it. Something was really wrong, though. I recorded something onto track 1 of the tape, and on playback, the VU meter on the deck looked OK but I was getting hardly any signal on my mixer. After running through the cabling and checking everything on the mixer, the cause of the problem appeared to be in the tape deck, but I had no idea what it was.

I posted a thread on homerecording.com and a few people suggested that it might be the relays on the amplifier cards. To be specific, there’s two relays on each amplifier card that control signal output. The 48 runs at either +4dB or -10dB, and these relays switch between the two sets of inputs and outputs. When they fail, they’ll often they fail simultanously, breaking on multiple channels. This made sense, as the problem soon spread to 4 of the 8 channels on the deck.

To make sure that its was the relays, I plugged the +4dB balanced outputs into a firewire interface and played a MRL testing/calibration tape several times, going from channel to channel each time. They all worked. This confirmed that it was indeed a problem with bad/dead relays.

After asking several more questions, I found out that the bad relays were the ones labeled “K003″ on the amplifier card. These relays are used when using the deck’s -10dB unbalanced outputs. The stock relay is an NEC component that is no longer manufactured, but a company called Hamlin makes a perfect replacement. It’s the HE721A2400, and it can be found at DigiKey for cheap.

Hamlin HE721A2400 Relays

Replacing the relays isn’t difficult but it requires some basic soldering skills. You will need a solder sucker; most decent electronics or hobby supply shops sell a basic model for $15-$20. Knowing how to use it is also important: I didn’t know how to use one and carelessly assumed that I could figure it out, and ended up damaging one of the cards (I repaired the damage, though). To remove a component from a circuit board, apply the soldering iron tip to the lead of the component on the “top” side of the board, while applying the solder sucker tip to the bottom of the lead on the “bottom” side of the board. When the solder appears to have melted, click the solder sucker and the molten solder gets sucked out of the drilled PCB hole and into the sucker. I wish I had a picture to demonstrate this, but reread the last sentence and ask any questions if it’s unclear.

After removing all of the K003 relays, I soldered IC sockets to the holes where the relays had been. I did this in case the relays need to be replaced in the future… saving myself or someone else some work. The relays snapped into the sockets easily. Here’s a picture of one of the replacement relays, in its socket:

Closeup of New Relay

I put the cards back into the deck, put the MRL tape on again, and everything worked just fine. I was so relieved to have it working again, and I was proud to have fixed it myself… with a lot of help, of course.

Notes:

• The Tascam 42, 44, and 48 share the same amp card design. This repair will work for any of these models.
• A full calibration should be done on the deck after replacing the relays. The relay’s performance seems to degrade over a period of weeks before completely breaking, and it might have been compensated for in different ways as it worsened over time. Bringing the deck to a solid, accurate state is definitely recommended.

Reel motor from Tascam 34b

Demo Clip Demo Clip Demo Clip:

Audio clip: Adobe Flash Player (version 9 or above) is required to play this audio clip. Download the latest version here. You also need to have JavaScript enabled in your browser.

It’s been nearly two weeks since I last wrote. I’m a bit bogged down in projects right now and I haven’t had much opportunity to make music.

A few technical issues have sprung up and I’m taking care of them as best I can. I was really hoping that I’d be out of the woods by now, equipment-wise, but it looks like I’m not there yet.

After eliminating most of the hums and buzzes from my studio, I hooked up my Tascam 48 eight track machine to the console and started recording. On playback, however, I noticed that four of the eight channels were producing weak signals. The needles on the VU meters looked right, and it wasn’t an issue with the mixing console. Something is happening in the amplification stage in the tape deck.

I opened up the machine and removed the amp cards to clean and inspect them. After putting them back in, the problem was still there and it appeared to follow the cards. That means that there’s something wrong with those individual amp cards. Maybe. I’m waiting to pick up a calibration tape, and I’ll start from the top and work to the bottom to find the problem and (hopefully) its solution.

Also, with my secondary Tascam 34b quarter-inch four track machine, I noticed problems with the reel motors on playback, fast forward, and rewind. When a tape is loaded, the motors will run at normal speed and then grind to a halt. So, I opened the deck, removed the motors, and gave them a full cleaning. I will also replace the bearings once I find a bearing puller to remove the old ones. I also replaced the belt, which I was going to do anyway.

Guts from Tascam 34b reel motor

This doesn’t touch on the issues that I’ve had with other equipment, but I should fix these two things before I move on to other projects. The eight-track is my primary multitrack, and the four-track machine will be very important for editing loops and for doing echo and delay. I kind of need them to work. You know.

- – -

I had a loop sitting on the bench, which I left there after I discovered that my eight track was broken. I put it on the working four-track deck and recorded it into Audacity. The original sound is a guitar chord, and I cut off the attack and made a loop from the remainder. This is one of my favorite techniques because the sounds that it produces are very glassy, and often sound like chimes. This was recorded in my bedroom, and I purposely EQed it to bring out the room sounds: my dehumidifier, street traffic, and general environmental white noise. It’s great as a demo, and I will eventually do it again in a proper studio for a more polished result.

- – -

I have a couple of building and design projects on my plate, too. I’m designing a loft bed for my bedroom. Underneath the bed will be a workspace, which means that I can get all of my broken tape decks off of the dining room table and into my personal space. I am also designing a shelf to go over the meter bridge of my mixer, which will hold a couple of lamps and my monitors. Finally, I’m designing a normaling RCA patchbay to handle the accessory send/receive jacks on my console. I will be writing a few posts about that later. Let me just say that it’s going to make this thing a LOT less messy:

Messy Patchbay

Anyway. Enjoy the clip. I’ve got some stuff to do.